AEG Washing Machine Error Codes

Washing Machine is useful Product from Every home And it is a product used in every home Sometimes it contains an error code. We can fix some error codes at home and we need to call a technician to fix some error codes. In this post you will find all the error codes of AEG washing machine and I hope you will benefit a lot from this post. If you find it helpful, please share this post.

Error Code	Problem
E10	The appliance does not fill with water properly.
E11	Poor fill before wash cycle. Tap off or water pressure too low; Drain hose improperly positioned; Fill valve is defective; Leaks on pressure switch; Pressure switch failed; Wiring fault; Main board defective. Cycle is paused with door locked Start
E12	Difficulty in fill during drying (maximum time 3 min. fill in drying during the wash load phase) Tap off or water pressure too low; valve failed; pressure switch water circuit; pressure switches; wiring; main PCB. Cycle is paused
E13	Water leaks. Drain hose improperly positioned; Water pressure too low; Fill valve is defective; Water circuit on pressure switch is leaking or blocked; Pressure switch faulty. Cycle is paused with door locked Start
E20	The appliance does not drain the water
E21	Poor draining. Drain hose kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; Main board faulty; Current leak between heating element and ground. Cycle is paused Start
E22	Difficulty in fill during drying or drying condenser blocked (pressure switch closed on “FULL”) Drain hose kinked; filter blocked: drying condenser blocked; drain pump faulty; pressure switches faulty; wiring; main circuit board faulty; Current leakage between heater and ground. Cycle is paused Start
E23	Defective triac for drain pump. Drain pump faulty; Wiring faulty; Main board faulty. Emergency drain procedure Cycle stops with door unlocked OFF/reset
E24	Malfunction in sensing circuit on triac for drain pump. Main board faulty. Emergency drain procedure. Cycle stops with door unlocked OFF/reset
E31	Malfunction in pressure switch circuit (frequency of signal from pressure switch out of limits) Pressure switch faulty; Wiring; Main PCB faulty; Cycle stops with door locked OFF/reset
E32	Electronic pressure switch improperly calibrated (level on electronic pressure switch differs from 0-66 mm after initial calibration drain and when anti-boiling pressure switch is on “empty”). Tap is off or water pressure is too low; Fill valve faulty; Water circuit on pressure switches; pressure switches; Wiring; PCB faulty; Cycle is paused Start
E33	Inconsistency between level on electronic pressure switch and level on anti-boiling pressure switch 1-2 (fault persists for at least 60 sec.). Pressure switch defective; Current leak between heating element and ground; Heating element; Wiring faulty; Main board faulty. Water circuit; Emergency drain procedure Cycle stops with door unlocked OFF/reset
E34	Inconsistency between level on electronic pressure switch and level on anti-boiling pressure switch 2 (fault persists for at least 60 sec.). Pressure switch faulty; Electrical current leak between heating element and ground; Heating element faulty; Wiring faulty; Main board faulty. Water circuit; Emergency drain procedure Cycle stops with door unlocked OFF/reset
E35	Overflow. Fill valve is faulty; Leaks from water circuit on pressure switch; Pressure switch defective; Wiring defective; Main board defective. Cycle stops. Emergency drain procedure. Drain pump continues to operate (5 min. on, then 5 min. off, etc.). OFF/reset
E36	Sensing circuit on anti-boiling pressure switch 1 defective Main board faulty. Cycle stops with door locked OFF/reset
E37	Sensing circuit on anti-boiling pressure switch 2 defective. Main board faulty. Cycle stops with door locked OFF/reset
E38	Internal pressure takeoff is blocked (water level does not change for at least 30 sec. of drum rotation). Water circuit on pressure switches; Pressure switches; Motor belt broken; Heating phase is skipped
E39	Defective HV sensing on anti-overflow system Main board faulty. Cycle stops with door locked OFF/reset
E40	The appliance door is open or not closed correctly. Please check the door!
E3A	Faulty sensing by heating resistance relay. Main board defective. Cycle stops with door locked OFF/reset
E41	Door unlocked. Door lock faulty; Wiring faulty; Main board faulty. Cycle is paused Start
E42	Problem closing the door. Door lock faulty; Wiring faulty; Main board faulty. Cycle is paused Start
E43	Defective triac supplying power to door delay system. Door lock unit faulty; Wiring faulty; Main board faulty. (Emergency drain procedure) Cycle stops OFF/reset
E44	Defective sensing by door delay system. Main board faulty. (Emergency drain procedure) Cycle stops OFF/reset
E45	Defective sensing by triac on door delay system. Main board faulty. (Emergency drain procedure) Cycle stops OFF/reset
E51	Motor power supply triac short-circuited. PCB faulty; current leakage from motor or from wiring loom. Cycle blocked, door locked (after 5 attempts) OFF/reset
E52	No signal from motor tachometric generator. Motor faulty; wiring faulty; PCB faulty Cycle blocked, door locked (after 5 attempts) OFF/reset
E53	Motor triac sensing circuit faulty. PCB faulty. Cycle blocked, door locked OFF/reset
E54	Motor relay contacts sticking. PCB faulty; current leakage from motor or from wiring Cycle blocked, door locked (after 5 attempts) OFF/reset
E61	Insufficient heating during washing. NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. The heating phase is skipped
E62	Overheating during washing. NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. Safety drain cycle Cycle stopped with door open OFF/reset
E66	Heating element power relay faulty. PCB faulty; current leakage from heating element to ground. Safety drain cycle Cycle stopped with door open OFF/reset
E71	NTC sensor for wash cycle defective. Faulty NTC sensor; Wiring faulty; Main board faulty. Heating is skipped Start
E72	Fault in NTC sensor on drying condenser (voltage out of range = short-circuit, open circuit) Drying NTC sensor (condenser) faulty; wiring faulty; main circuit board faulty. Heating is skipped Start
E73	Fault in NTC sensor on drying duct (voltage out of range = short-circuit, open circuit) Drying NTC sensor (duct) faulty; wiring faulty; main circuit board faulty. Heating is skipped Start
E74	NTC sensor for wash cycle improperly positioned. NTC sensor incorrectly positioned; Faulty NTC sensor; Wiring defective; Main board faulty. Heating is skipped Start
E82	Error in selector reset position. PCB faulty (Wrong configuration data). Selector, wiring faulty OFF/reset
E83	Error in reading selector. PCB faulty (Wrong configuration data). Selector, wiring Cycle cancelled
E84	“Sensing” circuit on circulation pump triac faulty (input signal to processor always 0V or 5V) PCB Drain, cycle blocked (door open) OFF/reset
E85	Circulation pump faulty (incongruency between status of “sensing” circuit on circulation pump and status of TRIAC) Circulation pump; wiring; main PCB Drain, cycle blocked (door open) OFF/reset
E91	Communication incongruence between main PCB- display board (versions not compatible) Wiring faulty; Faulty control/display board Main PCB faulty. Cycle interrupted
E92	Communication incongruence between main PCB- display board (versions not compatible) Wrong control/display board; Wrong PCB (do not correspond to the model). Cycle interrupted
E93	Incorrect configuration of appliance. Incorrect configuration data; PCB faulty. Cycle interrupted OFF/reset
E94	Incorrect configuration of washing cycle. Incorrect configuration data; PCB faulty. Cycle interrupted OFF/reset
E95	Communication error between microprocessor and EEPROM PCB faulty. Cycle interrupted OFF/reset
E97	Incongruence between programme selector and cycle configuration. Faulty PCB (Wrong configuration data). Cycle interrupted OFF/reset
EB1	Frequency of appliance incorrect. Power supply problems (incorrect / disturbance); PCB faulty. Cycle interrupted
EB2	Voltage too high. Power supply problems (incorrect / disturbance); PCB faulty. Cycle interrupted
EB3	Voltage too low. Power supply problems (incorrect / disturbance); PCB faulty. Cycle interrupted
EC1	Solenoid valve inoperative but flow meter operating. Main board faulty, Fill valve faulty Cycle stops with door locked (after 5 attempts). OFF/reset
EC2	Signal from turbidity sensor out of limits. Turbidity sensor faulty, Main board faulty, Wiring faulty Start/reset
EC3	Signal from weight sensor out of limits. Weight sensor faulty, Main board faulty, Wiring faulty Start/reset
EF0	The anti-flood device is on. Disconnect the appliance and close the water tap. Contact the Authorised Service Centre.
EF1	Drain filter blocked (too long drain phase) Drain tube blocked/kinked/too high; Drain filter dirty/blocked. Warning displayed at the end of cycle (specific LED)
EF2	Overdosing of detergent (too much foam during drain phases) Excessive detergent dosing; drain tube kinked/blocked; Drain filter dirty/blocked.
EF3	Control water intervention. Water leakage on the base; faulty water control device. Water drain and cycle blocked OFF/reset
EF4	Low pressure of water fill, no signal of flow meter and solenoid open Tap closed, low water fill pressure … Reset
E00	No alarm
EH0	The mains supply is unstable. Wait until the mains supply is stable.

AEG LAVAMAT Washing Machine Error Codes

Error Code	Problem
C1	Not filling/ too slow fill
C2	Not pumping/too slow pump output
C3	Aqua control activated
C7	Not heating
C8	NTC fault
C9	Tacho or motor fault
CA	Motor triac short circuit
CD	Door lock faulty
CE	Water distributor fault, this machine has a small motor in the dispenser to select the Compartment to fill through, this in turn operates a micro switch inside the dispenser.
CF	EPROM fault Some of these faults are locked in and will return even if machine is disconnected; the only way to clear them is to run the test programme. Hold in Pre wash and soak button while turning rotary knob to gentle spin.

LAVAMAT 8 Series Error Codes

Error Code	Problem
CO	lmbalance between both Pressure Switches, Heater or wiring fault.
C1	No water in, valve at fault or low pressure.
C2	Pump blockage, pump open circuit, drain blockage.
C3	Safety flood device operated, pump fault, module fault.
C4	Pump fault.
C5	Overheat sensor on main motor.
C6	Pressure switch fault.
C7	Heater or heater relay fault.
C8	NTC fault.
C9	Tacho fault.
CA	MOS-FET transitor defective.(Replace main module)
CB	Overfill/level fault or inlet valve.
CC	PTC for MOS-FET transistor fault, main motor fault.
CD	Door Interlock fault.
CF	Checksum EEPROM fault, configuration error on module.

AEG Washing Machines – Washer-Dryers Alarm Codes and Solutions

Alarm Code	Solution
E11	Difficulties in water fill for washing. Tap closed or water pressure too low; Drain tube improperly positioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty.
E12	Difficulties in water fill for drying. Tap closed or water pressure too low; Drain tube improperly positioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty.
E13	Water leakage. Drain hose incorrectly positioned; mains pressure insufficient; water fill solenoid faulty; leakage/blockage of pressure switch hydraulic circuit; pressure switch faulty.
E21	Difficulties in draining for washing. Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty.
E22	Difficulties in draining for drying. Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty.
E23	Drain pump triac faulty. Drain pump faulty; Wiring faulty; PCB faulty.
E24	Fault in “sensing” circuit of drain pump triac (wrong input signal to microprocessor) PCB faulty.
E31	Electronic pressure switch circuit faulty (frequency of pressure switch signal out of limits) Electronic pressure switch; Wiring; PCB faulty.
E32	Incorrect calibration of electronic pressure switch (The electronic pressure switch generates a signal with instable frequency during the drain phase). Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Leaks from water circuit on pressure switch; Pressure switch; Wiring faulty; PCB faulty.
E35	Water overflow. Water fill solenoid faulty; Leaks from water circuit on pressure switch; pressure switch faulty; wiring faulty; PCB faulty.
E38	Pressure chamber blocked (water level does not vary for at least 30 sec. during drum rotation) Motor drive belt broken; Hydraulic circuit pressure switch clogged.
E3A	Heating elem. relay sensing faulty (input signal to microprocessor always 0V or 5V) PCB faulty.
E41	Door open (after 15 sec.) Door interlock faulty; wiring faulty; PCB faulty.
E42	Problems of door closure. Door interlock faulty; wiring faulty; PCB faulty.
E43	Interlock power supply triac faulty. Door interlock faulty; wiring faulty; PCB faulty.
E44	Door interlock sensing circuit triac faulty. PCB faulty.
E45	Door interlock sensing circuit triac faulty (wrong input signal to microprocessor) PCB faulty.
E52	No signal from motor tachometric generator. Motor faulty; wiring faulty; PCB faulty.
E57	Inverter is drawing too much current (>15A). Motor-Inverter wiring faulty; Inverter board faulty, Motor faulty.
E58	Inverter is drawing too much current (>4,5A). Motor abnormal operation (overloaded); Motor-Inverter wiring faulty; Motor faulty; Inverter board faulty.
E59	No signal from tachometric generator for three seconds. Motor-Inverter wiring faulty; Inverter board faulty, Motor faulty.
E5A	Overheating for heat dissipator for Inverter. Overheating caused by continuous operation or ambient conditions (let appliance cool down); Inverter board faulty. NTC open (on the Inverter board).
E5H	Input voltage is lower than 175V. Wiring faulty; Inverter board faulty
E5C	Input voltage is too high. Input voltage is too high (measure the masters voltage); Inverter board faulty.
E5d	Data transfer error between Inverter and main board. Line interference; Wiring faulty; Main board or Inverter faulty.
E5E	Wrong communication between main board and Inverter. Main board-Inverter wiring faulty; Inverter board faulty; Main board faulty.
E5F	Inverter board does not start the motor. Wiring faulty; Inverter board faulty; Main board faulty.
E61	Insufficient heating during washing. NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty.
E62	Overheating during washing (temperature higher than 88°C for a time higher than 5 min.) NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty.
E66	Heating element power relay faulty (incongruence between sensing and relay) PCB faulty.
E68	Current dispersion to earth (value of mains voltage different from main value) Current dispersion between between heating element and earth.
E69	Heating element interrupted. Wiring faulty; Heating element for washing interrupted (thermofuse open)
E71	Washing NTC sensor faulty (short- circuited or open) Wiring faulty; Washing NTC sensor faulty; PCB faulty.
E72	Drying condenser NTC sensor faulty (voltage value out of limits, sensor short-circuited or open) Wiring faulty; Drying NTC sensor (condenser) badly positioned or faulty; WD board faulty.
E73	Drying duct NTC sensor faulty (voltage value out of limits, sensor short-circuited or open) Wiring faulty; Drying NTC sensor (duct) badly positioned or faulty; WD board faulty.
E74	Washing NTC sensor badly positioned. Wiring faulty; Washing NTC sensor badly positioned; NTC sensor faulty; PCB faulty.
E82	Error in selector reset position. PCB faulty (Wrong configuration data).
E83	Error in selector reading. PCB faulty (Wrong configuration data.
E91	Communication error between PCB and display board. Wiring faulty; Control/display board faulty: PCB faulty.
E92	Communication incongruence between main PCB- display board (versions not compatible) Wrong control/display board; Wrong PCB (do not correspond to the model).
E93	Incorrect configuration of appliance. PCB faulty; (Incorrect configuration data).
E94	Incorrect configuration of washing cycle. PCB faulty; (Incorrect configuration data).
E95	Communication error between microprocessor and EEPROM. PCB faulty
E97	Incongruence between programme selector and cycle configuration. Faulty PCB (Wrong configuration data).
E98	Communication error between main board – Inverter. Incompatibility between main board and Inverter.
E9H	Communication error between microprocessor and FLASH memory. Display board.
E9C	Machine configuration error. Display board.
E9d	Clock faulty. Display board.
E9F	Communication error between PCB and remote devices. Wiring between PCB and Inverter faulty; PCB faulty; Inverter faulty.
EA1	Drum positioning (DSP) faulty. Motor belt broken; Wiring faulty; PCB faulty; DSP sensor faulty.
EA6	DSP door opening faulty. Motor belt broken; Wiring faulty; Drum cover open. Motor faulty; PCB faulty.
EC1	Solenoid valve blocked with flowmeter working. Wiring faulty; Solenoid valve faulty/blocked, PCB faulty.
EC3	Problems with Weight sensor (no signal or out of limits) Wiring faulty; Weight sensor faulty; PCB faulty.
Ed1	Data communication error between WD board and PCB. Wiring faulty between PCB and WD board; WD board faulty; PCB faulty.
Ed2	Drying heating element relay 1 faulty. Wiring faulty between WD board and thermostats; thermostats faulty; WD board faulty, PCB faulty.
Ed3	Drying heating element relay 2 faulty. Wiring faulty between WD board and thermostats; thermostats faulty; WD board faulty, PCB faulty.
Ed4	Relay which commutates power between washing heating element and drying (in the WD board). Wiring faulty; WD board faulty; PCB faulty.
Ed6	No communication between PCB and display board (INPUT). Wiring faulty between PCB and programme display board; PCB faulty.
EF1	Drain filter blocked (drain phase too long) Drain tube blocked/kinked/too high; Drain filter dirty/blocked.
EF2	Excessive detergent dosing (excessive foam during draining) Excessive detergent dosing; drain tube kinked/blocked; Drain filter dirty/blocked.
EF3	Aqua control intervention. Water leaks onto base frame; water control system defective.
EF4	Water fill pressure low, no signal of flowmeter and solenoid valve open. Tap closed; water fill pressure low.
EF5	Unbalanced load. Final spin phases skipped.
EF6	Reset. No action to be performed, if continues replace the PCB.
EH1	Frequency power of appliance out of limits. Power supply problems (incorrect / disturbance); PCB faulty.
EH2	Voltage too high. Power supply problems (incorrect / disturbance); PCB faulty.
EH3	Voltage too low. Power supply problems (incorrect / disturbance); PCB faulty.
EHF	Safety “sensing” circuit faulty (input voltage to microprocessor wrong) PCB faulty.
EHE	Incongruence between safety relay (in the PCB) and the safety “sensing” circuit. Wiring faulty; PCB faulty.