Electrolux Washing Machine Error Codes
Washing Machine is useful Product from Every home And it is a product used in every home Sometimes it contains an error code. We can fix some error codes at home and we need to call a technician to fix some error codes. In this post you will find all the error codes of Electrolux washing machine and I hope you will benefit a lot from this post. If you find it helpful, please share this post.
| Error Codes | Problem |
|---|---|
| 01 | NO WATER. Water level has not reached set level within time set. After this error message appears and the machine is reset, the machine will try again. |
| 02 | DOOR OPEN. Signal from microswitch which checks door status absent during program. After this error message appears and the machine is reset, the machine will try again. |
| 03 | DOOR UNLOCKED. Signal from microswitch which detects when the door is locked absent during program. |
| 04 | NTC LOW TEMP. The temperature is below the lowest value allowed (open circuit in temperature sensor). |
| 05 | NTC HIGH TEMP. The temperature is above the highest value allowed (short-circuit in temperature sensor). |
| 06 | WATER IN DRUM. The water level is higher that the level EMPTY at the start of the program. |
| 07 | MACHINE OVER-FILLED. The water level is higher than the ”LEVEL OVERFILL” (i.e. DRUM OVER-FILLED) level. If this function is switched off (=N), instead the drain valve will open for a short time and discharge some of the water. This is described under the function ”DRAIN TIME WHEN OVERFILL” (i.e. DRAIN TIME AFTER OVER-FILLING) earlier in this section. |
| 08 | NO HEATING. The temperature has not increased by the number of degrees specified in the function ”MIN. TEMPERATURE INCREASE” (see back in this section), over the period of time specified in the function MAXIMUM HEATING TIME (see ”SETTINGS 1”). On machines built for washing mops, it can be caused by too low a level in the program stage. The lowest level for a mop program in the main wash with heating is 22 scale units. |
| 10 | NOT DRAINED. When the drain sequence has finished, the water level is still higher than the EMPTY level. |
| 11 | UNBALANCE SENSOR FAULT. The unbalance switch is closed when the machine is starting on a drain sequence. |
| 13 | NO MOTOR COMM. Communication between PCU and motor control unit interrupted or disturbed. |
| 14 | LEVEL CALIBRATION. Every machine has individual level calibration at the factory. If these calibration values are missing or fall outside the limit values, an error warning will be flagged at each program start-up. The program can still be started, however, by pressing START. It will then use standard (default) values, which means that the levels will not be as precise as intended. |
| 15 | EMERGENCY STOP. The emergency stop button has been pressed. |
| 16 | WEIGHT FROM SCALE. Over-/Under-load of scale or weight above limit for maximum allowed weight at wash module start. |
| 17 | DOOR LOCK. Even though the door lock microswitch indicates that the door is locked, the signal from the microswitch which is used to detect when the door is closed is absent. |
| 18 | START NOT ALLOWED. Network does not allow programme start. |
| 19 | MIS COMMUNICATION. Machine has lost contact with network. |
| 20 | INTERLOCK STATUS. The motor control system for frequency-controlled motors (EWD) receives a signal direct from the door lock which indicates that the door really is closed. If this signal is lost, a fault signal is sent to the PCU |
| 21 | I/O COMMUNICATION. Communication between the CPU board and one of the I/O boards interrupted or disturbed. |
| 22 | LOW OIL LEVEL. In machines with an oil lubrication system, indicates low level in the oil container. |
| 23 | PHASE. Incorrect input voltage to external equipment. |
| 24 | PRESSURE SENSOR TILT. Both pressure sensors are active at the same time |
| 25 | PRESSURE SENSOR TIMEOUT. No pressure at the relevant pressure sensor within the maximum time allowed for tilt backwards or forwards. |
| 26 | DOOR SWITCH, TILT. Door closed (S3) is “on” at a time when the machine door is locked open (S25).) |
| 27 | AUT. LEVEL CALIB. The pressure sensor for the water level signals a value that is so different from the empty machine state that the automatic level calibration cannot adjust the level system. |
| 28 | Calibration of level system not done in service mode before use of machine. |
| 31 | HEAT SINK TOO HOT. Temperature of MCU control circuits too high |
| 32 | MOTOR TOO HOT. Motor thermal protection has tripped |
| 33 | NO INTERLOCK. The motor has received a start command from the PCU without receiving an interlock signal from the door lock. The MCU receiving circuitry for the interlock signal is not faulty. |
| 35 | MOTOR SHORTNING. Short-circuit between motor windings or to earth. |
| 36 | INTERLOCK HARDWARE. Fault in MCU receiving circuitry for lock acknowledgement signal |
| 37 | LOW DC VOLTAGE. DC voltage too low |
| 38 | HIGH DC VOLTAGE. DC voltage too high |
| 39 | RIPPEL ON DC BUS. DC level varying too much |
| 40 | LINE INTERRUPT. One phase missing for/at motor control unit |
| 41 | KLIXON CIRCUITS. Hardware fault, temperature monitoring, motor |
| 42 | NO PARAM. SET IN MCU. The motor controller (MCU) (inverter) contains several different parameter sets for different motors. During power up the timer checks that the correct parameter set digit is written into the MCU. If not, the timer will write down the parameter set digit defined in fixed config. If the MCU discovers that no parameter set value is written down into the MCU, the error coce will be displayed. |
| E10 | The appliance does not fill with water properly. |
| E20 | The appliance does not drain the water. |
| E40 | The appliance door is open or not closed correctly. Please check the door! |
| EH0 | The main supply is unstable. Wait until the main supply is stable. |
| E91 | No communication between electronic elements of the appliance. Switch off and switch on again. |
Washing Machines & Washer-Dryers Alarm Codes
| Alarm Codes | Solutions |
|---|---|
| E11 | Difficulties in water fill for washing. Tap closed or water pressure too low; Drain tube improperly positioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty. |
| E12 | Difficulties in water fill for drying. Tap closed or water pressure too low; Drain tube improperly positioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty. |
| E13 | Water leakage. Drain hose incorrectly positioned; mains pressure insufficient; water fill solenoid faulty; leakage/blockage of pressure switch hydraulic circuit; pressure switch faulty. |
| E21 | Difficulties in draining for washing. Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty. |
| E22 | Difficulties in draining for drying. Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty. |
| E23 | Drain pump triac faulty. Drain pump faulty; Wiring faulty; PCB faulty. |
| E24 | Fault in “sensing” circuit of drain pump triac (wrong input signal to microprocessor) PCB faulty. |
| E31 | Electronic pressure switch circuit faulty (frequency of pressure switch signal out of limits) Electronic pressure switch; Wiring; PCB faulty. |
| E32 | Incorrect calibration of electronic pressure switch (The electronic pressure switch generates a signal with instable frequency during the drain phase). Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Leaks from water circuit on pressure switch; Pressure switch; Wiring faulty; PCB faulty. |
| E35 | Water overflow. Water fill solenoid faulty; Leaks from water circuit on pressure switch; pressure switch faulty; wiring faulty; PCB faulty. |
| E38 | Pressure chamber blocked (water level does not vary for at least 30 sec. during drum rotation) Motor drive belt broken; Hydraulic circuit pressure switch clogged. |
| E3A | Heating elem. relay sensing faulty (input signal to microprocessor always 0V or 5V) PCB faulty. |
| E41 | Door open (after 15 sec.) Door interlock faulty; wiring faulty; PCB faulty. |
| E42 | Problems of door closure. Door interlock faulty; wiring faulty; PCB faulty. |
| E43 | Interlock power supply triac faulty. Door interlock faulty; wiring faulty; PCB faulty. |
| E44 | Door interlock sensing circuit triac faulty. PCB faulty. |
| E45 | Door interlock sensing circuit triac faulty (wrong input signal to microprocessor) PCB faulty. |
| E52 | No signal from motor tachometric generator. Motor faulty; wiring faulty; PCB faulty. |
| E57 | Inverter is drawing too much current (>15A). Motor-Inverter wiring faulty; Inverter board faulty, Motor faulty. |
| E58 | Inverter is drawing too much current (>4,5A). Motor abnormal operation (overloaded); Motor-Inverter wiring faulty; Motor faulty; Inverter board faulty. |
| E59 | No signal from tachometric generator for three seconds. Motor-Inverter wiring faulty; Inverter board faulty, Motor faulty. |
| E5A | Overheating for heat dissipator for Inverter. Overheating caused by continuous operation or ambient conditions (let appliance cool down); Inverter board faulty. NTC open (on the Inverter board). |
| E5H | Input voltage is lower than 175V. Wiring faulty; Inverter board faulty |
| E5C | Input voltage is too high. Input voltage is too high (measure the masters voltage); Inverter board faulty. |
| E5d | Data transfer error between Inverter and main board. Line interference; Wiring faulty; Main board or Inverter faulty. |
| E5E | Wrong communication between main board and Inverter. Main board-Inverter wiring faulty; Inverter board faulty; Main board faulty. |
| E5F | Inverter board does not start the motor. Wiring faulty; Inverter board faulty; Main board faulty. |
| E61 | Insufficient heating during washing. NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. |
| E62 | Overheating during washing (temperature higher than 88°C for a time higher than 5 min.) NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. |
| E66 | Heating element power relay faulty (incongruence between sensing and relay) PCB faulty. |
| E68 | Current dispersion to earth (value of mains voltage different from main value) Current dispersion between between heating element and earth. |
| E69 | Heating element interrupted. Wiring faulty; Heating element for washing interrupted (thermofuse open) |
| E71 | Washing NTC sensor faulty (short- circuited or open) Wiring faulty; Washing NTC sensor faulty; PCB faulty. |
| E72 | Drying condenser NTC sensor faulty (voltage value out of limits, sensor short-circuited or open) Wiring faulty; Drying NTC sensor (condenser) badly positioned or faulty; WD board faulty. |
| E73 | Drying duct NTC sensor faulty (voltage value out of limits, sensor short-circuited or open) Wiring faulty; Drying NTC sensor (duct) badly positioned or faulty; WD board faulty. |
| E74 | Washing NTC sensor badly positioned. Wiring faulty; Washing NTC sensor badly positioned; NTC sensor faulty; PCB faulty. |
| E82 | Error in selector reset position. PCB faulty (Wrong configuration data). |
| E83 | Error in selector reading. PCB faulty (Wrong configuration data. |
| E91 | Communication error between PCB and display board. Wiring faulty; Control/display board faulty: PCB faulty. |
| E92 | Communication incongruence between main PCB- display board (versions not compatible) Wrong control/display board; Wrong PCB (do not correspond to the model). |
| E93 | Incorrect configuration of appliance. PCB faulty; (Incorrect configuration data). |
| E94 | Incorrect configuration of washing cycle. PCB faulty; (Incorrect configuration data). |
| E95 | Communication error between microprocessor and EEPROM. PCB faulty |
| E97 | Incongruence between programme selector and cycle configuration. Faulty PCB (Wrong configuration data). |
| E98 | Communication error between main board – Inverter. Incompatibility between main board and Inverter. |
| E9H | Communication error between microprocessor and FLASH memory. Display board. |
| E9C | Machine configuration error. Display board. |
| E9d | Clock faulty. Display board. |
| E9F | Communication error between PCB and remote devices. Wiring between PCB and Inverter faulty; PCB faulty; Inverter faulty. |
| EA1 | Drum positioning (DSP) faulty. Motor belt broken; Wiring faulty; PCB faulty; DSP sensor faulty. |
| EA6 | DSP door opening faulty. Motor belt broken; Wiring faulty; Drum cover open. Motor faulty; PCB faulty. |
| EC1 | Solenoid valve blocked with flowmeter working. Wiring faulty; Solenoid valve faulty/blocked, PCB faulty. |
| EC3 | Problems with Weight sensor (no signal or out of limits) Wiring faulty; Weight sensor faulty; PCB faulty. |
| Ed1 | Data communication error between WD board and PCB. Wiring faulty between PCB and WD board; WD board faulty; PCB faulty. |
| Ed2 | Drying heating element relay 1 faulty. Wiring faulty between WD board and thermostats; thermostats faulty; WD board faulty, PCB faulty. |
| Ed3 | Drying heating element relay 2 faulty. Wiring faulty between WD board and thermostats; thermostats faulty; WD board faulty, PCB faulty. |
| Ed4 | Relay which commutates power between washing heating element and drying (in the WD board). Wiring faulty; WD board faulty; PCB faulty. |
| Ed6 | No communication between PCB and display board (INPUT). Wiring faulty between PCB and programme display board; PCB faulty. |
| EF1 | Drain filter blocked (drain phase too long) Drain tube blocked/kinked/too high; Drain filter dirty/blocked. |
| EF2 | Excessive detergent dosing (excessive foam during draining) Excessive detergent dosing; drain tube kinked/blocked; Drain filter dirty/blocked. |
| EF3 | Aqua control intervention. Water leaks onto base frame; water control system defective. |
| EF4 | Water fill pressure low, no signal of flowmeter and solenoid valve open. Tap closed; water fill pressure low. |
| EF5 | Unbalanced load. Final spin phases skipped. |
| EF6 | Reset. No action to be performed, if continues replace the PCB. |
| EH1 | Frequency power of appliance out of limits. Power supply problems (incorrect / disturbance); PCB faulty. |
| EH2 | Voltage too high. Power supply problems (incorrect / disturbance); PCB faulty. |
| EH3 | Voltage too low. Power supply problems (incorrect / disturbance); PCB faulty. |
| EHE | Incongruence between safety relay (in the PCB) and the safety “sensing” circuit. Wiring faulty; PCB faulty. |
| EHF | Safety “sensing” circuit faulty (input voltage to microprocessor wrong) PCB faulty. |
Electrolux Washing Machine Manual PDF
